25LC Kbit SPI Bus Serial EEPROM The Microchip Technology Inc. 25AA/25LC *? Byte and Page-level Write Operations (25XX) is a 25LCI/SN Microchip Technology EEPROM k 64Kx8 V SER EE IND datasheet, inventory & pricing. 25LCI/SN from MICROCHIP >> Specification: EEPROM, Serial SPI, Kbit, 64K x 8bit, 20 MHz, SOIC, Technical Datasheet: 25LCI/SN Datasheet.

Author: Dumi Tugar
Country: Argentina
Language: English (Spanish)
Genre: Business
Published (Last): 20 May 2015
Pages: 118
PDF File Size: 13.40 Mb
ePub File Size: 11.50 Mb
ISBN: 462-8-36335-808-3
Downloads: 6973
Price: Free* [*Free Regsitration Required]
Uploader: Akinozil

Serial Peripheral Interface SPI is a synchronous serial data protocol used by Microcontrollers for communicating with one or more peripheral devices quickly over short distances. Pre-processor directives are processed before the actual compilation 25ld512. The 25LC has byte pages and functions that operate in byte mode and some in page mode.

Then I try to read the value from address 0: I have also checked clock with an oscilloscope not logic analyzer on hand unfortunately. Additionally, I did create a ns and microsecond delay functions I can also test as well, but I’ll try the ms delay with the system tick first.

This datashfet that any write operation, no matter how few bytes, takes the same amount of time, about 3. Next we send our bytes of data from our buffer dtasheet, one byte after another without pause.

Send them to support ccsinfo.

It really helped me! You didn’t post your SSP send and receive functions, but that’s probably where your problem is. Also, it is an analog scope, so it is hard to tell the frequency by counting the ticks when the time division can go high enough.

  DUA E GANJUL ARSH IN ARABIC PDF

My scope is rated at 20MHz, but the highest time division setting is ns which is 5MHz. Can you see the bytes you have sent? Hello Nick, here are some points, i have seeing in your listing: Here is a simple layout of the connections: Catasheet edited by treitmey on Fri Datasbeet 20, Since this is undesirable most of the time, the code below makes the page boundaries transparent for write operations.

When the address increments to we turn it back to 0 because we have only filled addresses in the EEPROM with data:. We send the 16 bit address to begin writing at in two bytes, Most Significant Bit first. Connect 5V power and ground from the breadboard to datasneet power and ground from the microcontroller.

Data Sheets

The device also offers various degerees of write protection and a hold pin, but we won’t be covering those in this tutorial. Note char buffer []. Very helpful with SPI! From the datasheet, the delay has to be about ns. Sign in Sign in Remember me Forgot username or password? This will force the entire page to endure a write cycle, for this reason endurance is specified per page.

Fri Jul 20, 1: The first step is setting up our pre-processor directives. Datasehet you show what configuration parameter you are using?

Before entering the main while loop I put in a value 0xF9 at address 0: I guess in the end i just want to know if its worth going through the trouble of using my 1M Write cycles conservatively in B page writes instead of doing 64k individual byte writes Note that the chip on the Arduino board contains an internal EEPROM, so follow this tutorial only if you need more datasheer than it provides.

  HSWA 1974 PDF

When writing to the 25LC, all bytes in a page are refreshed even if fewer are written. It looks like they already have done the heavy lifting for me in regard to setting up the clock and power.

They start with a ” ” and do not end with semi-colons. Here is what the read statement look like within the main while loop now: And the Program for my task is: Have you checked the data which is received? I see what appears to be pulse more like sloped triangles. Here we allocate the global variables we will be datawheet later in the program.

25LC Datasheet(PDF) – Microchip Technology

Typically there are three lines common to all the devices. Status registers change their state based on various microcontroller conditions.

Control registers code control settings for various microcontroller functionalities. Anything above that will make it work just fine. Generally speaking there are three modes of transmission numbered 0 – 3.