ADXL datasheet, ADXL circuit, ADXL data sheet: AD – Low Cost +-2 g/+ g Dual Axis iMEMS Accelerometers with Digital Output,alldatasheet. ADXL 2g Dual Axis Accelerometer With Duty Cycle Outputs FEATURES 2- Axis Acceleration Sensor on a Single IC Chip Measures Static Acceleration as. ADXL Accelerometers are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for ADXL Accelerometers.

Author: Voodoojind Mazuk
Country: Sri Lanka
Language: English (Spanish)
Genre: Software
Published (Last): 21 August 2008
Pages: 405
PDF File Size: 1.32 Mb
ePub File Size: 4.5 Mb
ISBN: 325-4-52575-872-9
Downloads: 4273
Price: Free* [*Free Regsitration Required]
Uploader: Akicage

Typical Supply Current vs.

When the accelerometer is perpendicular to gravity, its output will change nearly At this orientation its sensitivity to changes in tilt is highest. Thomas Jefferson, Declaration of Independence. With the single pole roll-off characteristic, the typical noise of the ADXLE is determined by the following equation: Documents Flashcards Grammar checker. An op amp follower may be required to buffer this pin.

The following table shows some of the trade-offs. This will result in greater dynamic error generated at the DCM. This pin may be left open circuit or connected to common in normal use. Duty Cycle Filtering An analog output can be reconstructed by filtering the duty cycle output.

Polysilicon springs suspend the structure over the surface of the wafer and provide a resistance against acceleration forces.

  ELIPHAS LEVI EL GRAN ARCANO DEL OCULTISMO REVELADO PDF

Deflection of the structure is measured using a differential capacitor that consists of independent fixed plates and central plates attached to the moving mass. This technique requires only passive components. The actual resolution of the acceleration signal is, however, limited by the time resolution of the counting devices used to decode the duty cycle.

ADXL Datasheet pdf – ±2 g Dual Axis Accelerometer – Analog Devices

Application notes outlining algorithms for calculating acceleration from duty cycle and automated calibration routines are available from the factory. Run the accelerometer at a Lower Voltage, Down to 3 V. Note that the accelerometer offset and sensitivity adx,202 ratiometric to the supply voltage. Care should be exercised in handling to avoid damage. Specifications subject to change without notice.

Exposure to absolute maximum rating conditions for extended periods may affect device reliability. However, in axdl202 cases, especially where digital devices such as microcontrollers share the same power supply, digital noise on the supply may cause interference on the ADXLE output.

ADXL202 Data Sheet

A buffer amplifier is recommended, and may be required in any case to amplify the analog output to give enough resolution with an 8-bit to bit converter. The outputs are analog voltage or digital signals whose duty cycles ratio of pulsewidth to period are proportional to acceleration.

The equation for the 3 dB bandwidth is: Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. The analog output signal will be ratiometric to the supply voltage.

  ANDREI COSMOVICI PSIHOLOGIE SCOLARA PDF

At this point a pin datassheet available on each channel to allow the user to set the signal bandwidth of the device by adding a capacitor. The microcontroller should have provisions for software calibration. This filtering improves measurement resolution and helps prevent aliasing. This is a stress rating only; functional operation of the device at these or any other conditions above those indicate in the opera tional sections of this specification is not implied.

A minimum capacitance of pF for C X, Y is required in all cases. An acceleration will deflect the beam and unbalance the differential capacitor, resulting in an output square wave whose amplitude is proportional to acceleration.

Capacitors must be added at these pins to implement low-pass filtering for antialiasing and noise reduction. The second relates to the measurement resolution of the counter when decoding the duty cycle output. The faster the counter clock, the higher the resolution of the duty cycle and the shorter the T2 period can be for a given resolution.

Filtering can be used to lower the noise floor and improve the resolution of ddatasheet accelerometer.