ASTM A/AM: Standard Specification for Electric-Resistance-Welded Metallic-Coated Carbon Steel Mechanical Tubing. A Mechanical Tubing. ASTM A includes steel grades from – Alro stocks A as welded mechanical tubing. A Tube includes a wide. Designation: A – Standard Specification for. Electric-Resistance-Welded Metallic-Coated Carbon Steel Mechanical Tubing1 This standard is issued.

Author: Gojinn Barr
Country: Norway
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 16 August 2018
Pages: 495
PDF File Size: 7.10 Mb
ePub File Size: 4.66 Mb
ISBN: 349-5-31688-387-9
Downloads: 85422
Price: Free* [*Free Regsitration Required]
Uploader: Maunos

It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

A Type 6 Tubing provides a high degree of corrosion resistance and an excellent surface appearance and is a bridge between stainless and hot-dip galvanized finishes.

This abstract is a brief summary of the referenced standard. This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order specifies the applicable M specification designation SI unitsthe ashm units shall apply.

Wall thickness tolerances for premetallic coated as-welded tubing and diameter tolerances for metallic-coated round tubing shall be provided.

Within the text, the SI units are shown in brackets. We manufacture of ASTM A TYPE 1 Tubingis produced using aluminized steel which is carbon steel that has been pre-coated on both sides with an aluminum silicon alloy while in coil form. Link to Active This link will always route to the current Active version of the standard.

  DERECHO ROMANO CURSO DE DERECHO PRIVADO SABINO VENTURA SILVA PDF

ASTM A787 Grade 1018

The steels shall conform to elemental tolerances for product analysis. Within the text, the SI units are shown in brackets. Sizes outside the ranges ast, above may be ordered provided all other requirements of the specification are met. Combining values from the two systems may result in non-conformance with the standard.

Combining values from the two systems may result in non-conformance with the standard. Outside Diameter Tange, in. Carbon Steel A Tube Exporter.

This guide covers standard specification for round, square, rectangular, and special shape, electric-resistance-welded mechanical tubing, either zinc-coated galvanized after welding or produced from aluminum-coated, zinc-coated galvanizedzinc-iron alloy-coated galvannealedor aluminum-zinc alloy-coated steel sheet.

Low-carbon steels and other carbon steels shall conform to the required chemical composition for carbon, manganese, phosphorus, and sulfur.

Historical Version s – view previous versions of standard.

ASTM A Tubing ,ASTM A Type 1,Type 2,Type 3,Type 4,Type 6,ASTM A | Superior Steel

The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in either SI units or inch-pound units are to be regarded separately as standard. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.

  BOSCH GSB 500 RE MANUAL PDF

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. ASTM A Type 4 welded mechanical tubing is produced using carbon steel that has been pre-coated with a thin layer of zinc while in coil form and then heat treated to convert the coating into a zinc-iron alloy. ASTM Atm Type 3 welded mechanical tubing is produced out of a hot rolled carbon steel and then is hot-dip galvanized per ASTM A specification into a tank of molten zinc after the tubing is already formed and welded.

ASTM A Type 6 welded mechanical tubing is produced using steel that has been pre-coated with a thin layer of a zinc-aluminum-magnesium alloy coating while in coil form aatm specified in ASTM A