ASTM A/AM: Standard Specification for Electric-Resistance-Welded Metallic-Coated Carbon Steel Mechanical Tubing. A Mechanical Tubing. ASTM A includes steel grades from – Alro stocks A as welded mechanical tubing. A Tube includes a wide. Designation: A – Standard Specification for. Electric-Resistance-Welded Metallic-Coated Carbon Steel Mechanical Tubing1 This standard is issued.
|Published (Last):||17 December 2011|
|PDF File Size:||13.13 Mb|
|ePub File Size:||6.27 Mb|
|Price:||Free* [*Free Regsitration Required]|
Within the text, the SI units are shown in brackets. We manufacture of ASTM A TYPE 1 Tubingis produced using aluminized steel which is carbon steel that has been pre-coated on both sides with an aluminum silicon alloy while aa787 coil form. Carbon Steel A Tube Exporter. Sizes outside the ranges listed above may be ordered provided all other requirements of the specification are met.
The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. The steels shall conform to elemental tolerances for product analysis.
ASTM A Tubing ,ASTM A Type 1,Type 2,Type 3,Type 4,Type 6,ASTM A | Superior Steel
Link to Active This link will always route to the current Active version of the standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. A Type 6 Tubing provides a astj degree of corrosion resistance and an excellent surface appearance and is a bridge between stainless and hot-dip galvanized finishes.
A Mechanical Tubing | Alro Steel
Combining values from the two systems may result in non-conformance with the standard. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
Wall thickness tolerances for premetallic coated as-welded tubing and diameter tolerances for metallic-coated round tubing shall be provided. ASTM A Type 4 welded mechanical tubing is produced using carbon steel that has been pre-coated with a thin layer of zinc while in coil form and then heat treated to convert the coating into a zinc-iron alloy.
Combining values from the two systems may result in non-conformance with the standard. Within the text, the SI units are shown in brackets.
ASTM A787 Carbon Steel Tubing Manufacturer in India
The values stated in either SI units or inch-pound units are to be regarded separately as standard. ASTM A A778 3 welded mechanical tubing is produced out of a hot rolled carbon steel and then is hot-dip galvanized per ASTM A specification into a tank of molten zinc after the tubing is already formed and welded.
This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order specifies the applicable M specification designation SI unitsthe inch-pound units shall apply.
Low-carbon steels and other carbon steels shall conform to the required chemical composition for carbon, manganese, phosphorus, and sulfur.
The values stated in either SI units or inch-pound units are to be regarded separately as standard. Outside Diameter Tange, in. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.
ASTM A Type 6 welded mechanical tubing is produced using steel that has been pre-coated with a thin layer of a zinc-aluminum-magnesium alloy coating while in coil form as specified in ASTM A Historical Version s – view previous versions of standard.
This guide covers standard specification for round, square, rectangular, and special shape, electric-resistance-welded mechanical tubing, either zinc-coated galvanized after welding or produced from aluminum-coated, zinc-coated galvanizedzinc-iron alloy-coated galvannealedor aluminum-zinc alloy-coated steel sheet. This abstract is a brief summary of the referenced standard.