Find the most up-to-date version of ASTM C at Engineering ASTM C pdf – Download as PDF File .pdf), Text File .txt) or read online. ASTM C Standard Test Methods for Concrete Pipe, Manhole Sections, or Tile (External Load Crushing Strength). Lab ID: Use To determine first-crack.

Author: Kisho Mezigis
Country: Congo
Language: English (Spanish)
Genre: Medical
Published (Last): 22 February 2016
Pages: 413
PDF File Size: 10.94 Mb
ePub File Size: 20.67 Mb
ISBN: 272-3-61008-748-6
Downloads: 42575
Price: Free* [*Free Regsitration Required]
Uploader: Zulkikinos

ASTM C – 98 Standard Test Methods for Concrete Pipe, Manhole Sections, or Tile NO_PDF

If leakage of the joint initially occurs, the manufacturer is not prohibited from extending the test asmt up to a maximum of 24 h. This standard is subject awtm revision at any time by the responsible technical committee and must be reviewed every? If being tested in a horizontal position, the gage shall be placed to measure pressure at or as close to as practical above the horizontal axis.

Joint Shear Test The bearing faces of the lower strips shall not vary from a straight line vertically or horizontally by more than 1? If the pipe shows moist or damp spots on the outer surface of the pipe at that time, continue the tests for a period not to exceed 24 h at the option of the manufacturer.

All current methods of concrete pipe design assume that the installed pipes are uniformly bedded along the length of the pipeline. The shear strength limit shall be noted by a sudden reduction in the applied load or shearing of the concrete.

  GEOCORIS PUNCTIPES PDF

There shall be no visible leakage. Additional timber blocks or similar astk are necessary to elevate the test pipes. The rigid base shall be at least 6 in. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Do not apply live steam to the water to shorten the preboil period until 1 h of heating by gas or electricity has been completed.

Make an index mark on the gasket cross-section with the? The attachments from the heads of each testing device to the rung of the step are to be sufficiently sturdy to preclude any bending of the attachment and rung over the length of the attachment.

The total shear force on the joint is the sum asm the resultants of the pipe weight and the applied force. Hydrostatic External Joint Test Method.

It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. Hydrostatic Test Method 8. Welded Splice Pull Test. The joint is de? This rate of loading shall be continuous until the speci?

ASTM C497 – 18

The bearing face of the upper bearing shall not deviate from a straight line by more than 1? The difference in measurements is the stretched gasket height. A number in parentheses indicates the year of last reapproval. NOTE 3—Ultimate strength of concrete pipe in the buried condition is dependent on varying soil bedding factors and varying failure modes and shall have no relationship to the ultimate strength as de?

  AFICIO INSULATION CATALOGUE PDF

Gasket Lubricant Tests Then remove the specimens and weigh in accordance with 7. The alkalinity rating of the concrete mixture is one of the design asttm used to predict the service life of concrete pipelines where hydrogen sul? Use distilled water, rain water, or tap water that is known to have no effect on test results. Place the upper bearing so that it is aligned with these marks.

Report the results separately for each specimen. Atm gasket length is the distance measured at the point where the index mark retouches the scale.

When a hard v497 strip is used on the bearing face it shall have a durometer hardness of not less than 45 nor more than 60, and shall have a width of not less than 2 in. If both the design strength and the ultimate strength are being determined, a speci?

Moisture or beads of water appearing on the surface of the joint shall not be considered as leakage.

Each core sample is then placed in a separate container and dried in an oven for one to two hours at a temperature between and degrees Fahrenheit. Manhole Step Test Methods C97 edition approved Oct. They shall be rectangular in cross section, having a width of not less than 2 in.