BASE. 3. EMITTER. See detailed ordering and shipping information in the package dimensions section on page 5 of this data sheet. ORDERING INFORMATION. BCA Datasheet, BCA PDF, BCA Data sheet, BCA manual, Electronic Components Datasheet Search Included, No Data, *BC*(4). BF Transistor Datasheet pdf, BF Equivalent. Parameters and Characteristics.

Author: Tokasa Kazrakree
Country: Anguilla
Language: English (Spanish)
Genre: Software
Published (Last): 8 November 2017
Pages: 36
PDF File Size: 8.98 Mb
ePub File Size: 13.95 Mb
ISBN: 117-5-17485-971-2
Downloads: 54546
Price: Free* [*Free Regsitration Required]
Uploader: Moran

BC is a NPN transistor hence the collector and emitter will be left open Reverse biased when the base pin is held at ground and will be closed Forward biased when a signal is provided to base pin.

Transistor BC547

The value of I B should not exceed mA. March Learn how and when to remove this template message. TL — Programmable Reference Voltage. Complete Technical Details can be found at the datasheet give at the end of this page. Electronics Circuits and Systems.

When uses as an Amplifier the DC current gain of the Transistor can be calculated by using the below formulae. Build and Design Your Own Robots. All articles with unsourced statements Articles with unsourced statements from March Articles needing additional references from March All articles needing additional references. The BC part number is datashert by Pro Electronwhich allows many manufacturers to offer electrically and physically interchangeable parts under one identification. Unsourced material may be challenged and removed.

BC is mainly used for amplification bc47 switching purposes.

It is notably often the first type of bipolar transistor hobbyists encounter and is often featured in designs in hobby electronics magazines where a general-purpose transistor is required. From Wikipedia, the free encyclopedia. Skip to main content.


This is known as the biasing. The voltage divider is the commonly used biasing mode. Arduino based GPS receiver. It can amplify power, voltage and current at different dtasheet. To bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA. There is lot of variation in the ft-transition maximum frequency from manufacturer to manufacturer.

Interface GPS with Arduino. See the BC family for a table of these differences, and comparisons with predecessor types. Retrieved 8 March A transistor, stands for transfer of resistance, is commonly used to amplify current. Retrieved 28 March Choosing Battery for Robots.

Amplifier modules like Audio amplifiers, signal Amplifier etc. What is Web Browser. For switching applications, transistor is biased so that it remains fully on if there is a signal at its base. SPI Module of Arduino. As viewed in the top-right image, going from left to right, the pinout is as follows:. If you are designing a PCD or Datasjeet board with this component then the following picture from the Datasheet will be useful to know its package type and dimensions.

Interface SD Card with Arduino.

This page was last edited on 17 Dafasheetat When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV. The transistor terminals require a fixed DC dwtasheet to operate in the desired region of its characteristic curves. Some manufacturers place slightly different limits on the gain groups, for example the “B” group has been quoted as in a Philips datasheet.

BF Datasheet, Equivalent, Cross Reference Search. Transistor Catalog

A Transistors acts as an Amplifier when operating in Active Region. In other projects Wikimedia Commons. The assignment of transistor elements b,c,e to leads, i. Commercial transistors Bipolar transistors. The same letters are used for this purpose in several other European transistors, and is similar in principle to the “Yellow”, “Blue” and so on gain groupings in Japanese transistors, but should not be confused with the “A” suffix used with ratasheet American JEDEC devices, such as the 2NA, to indicate a variety of differences or enhancements over the base type.


The type number of any of the devices in this “family” may be followed by a letter, “A” to “C”, indicating devices that have been selected that fall within a narrow range of gain h FE.

Philips – datasheet pdf

By using this site, you agree to the Terms of Use and Privacy Policy. Devices registered to this Pro Electron number must have the following minimum performance characteristics: Views Read Edit View history. So a BC might have a current gain anywhere between andbut the gain of a BCA would be within the range of to Of the above types common emitter type is the popular and mostly used configuration. For amplification applications, the transistor is biased such that it is partly on for all input conditions.

The value of this resistor R B can be calculated using below formulae. As discussed a transistor will act as an Open switch during Forward Bias and as a Closed switch during Reverse Bias, this biasing can be achieved by supplying the required amount of current to the base pin.