EIC Cryo Cryogenic Pump & Expander Catalog | Ebara International Cryodynamics Division. Cryodynamics ®. For over 40 years, Cryodynamics® has been the premier manufacturer of both standard and custom cryogenic pumps and expanders. Ebara Cryogenic Pumps are applied in three distinct configurations: In addition to Cryogenic Pumps, Ebara Cryodynamics’ Expanders exemplify our drive for.

Author: Dishakar Julkis
Country: Botswana
Language: English (Spanish)
Genre: Career
Published (Last): 8 October 2013
Pages: 292
PDF File Size: 8.17 Mb
ePub File Size: 12.17 Mb
ISBN: 493-8-79021-218-8
Downloads: 47646
Price: Free* [*Free Regsitration Required]
Uploader: Shagor

To isolate the tank contents from the pump column, a suction valve is used, which incorporates a dual pressure sensitive seal.

In-Tank (Retractable)

It is fabricated with a suction nozzle, welded couplings for drain and liquid level indicationsupport brackets, a head plate crhogenic discharge nozzle, a conduit for electrical cables and a vent nozzle. These pumps are of similar construction to the ECC type and are usually located within the refrigerated cargo tank of a marine gas carrier to transfer such fluids as LNG, LPG, Ethylene, etc.

Special designs with built-in internal filtration are available to handle cargoes that are likely to suffer particulate contamination such as LPG. In-Tank Retractable ECR Type This unique design allows the pump to be installed inside a storage tank in cryogeic vertical pump column, with a suction foot valve located at the bottom. By combining the use of radial diffusers, which allows a much shorter stage length, with a much larger shaft diameter, the rotor becomes much more stable, normally operating cryoyenic below the first critical speed.

The valve is opened by lowering the pump into the valve.

In-Tank (Retractable) | Ebara International Cryodynamics Division

The units are fixed to the bottom of the tanks using a mounting arrangement designed to minimize stresses, and are connected directly to the discharge piping, which then travels out through the tops of the tanks. This unique design allows the pump to be installed inside a storage tank in a vertical pump column with a suction foot valve located at the bottom.

The column then acts as a guide to seat the pump during installation and also as the discharge pipe from the pump to the top of the tank.

This new design has proven to be extremely reliable in send-out systems which require a large, multi-stage pump to perform on a continuous, 24 hour-per-day basis. Because the pump is installed through the top of the tank, all connections below the maximum liquid level of the tank can be eliminated. Electric power feed cables and deck penetration assemblies provided by Cryodynamics meet the requirements of all the major ship classification societies.

  BASIC BIBLE INTERPRETATION BY ROY ZUCK PDF

The entire pump and motor assembly are contained within a suction vessel built to the appropriate pressure vessel code for each application, making the installation safe, simple and reliable. The submerged pump and motor unit is designed to fit into the smallest practical column puml by using an axial diffuser design.

As a result of the pump being installed through the top of the tank, all connections below the maximum liquid level of the tank can be eliminated. Each pump is fitted with an inducer which is an axial flow impeller located at the lowest possible level of the tank to improve the NPSHR Net Positive Suction Head Required ; allowing operators to lower tank liquid levels to extremely low levels.

EIC Cryo Cryogenic Pump & Expander Catalog

The main in-tank power cables are Cryodynamics UL listed armored cables, and can be provided in all voltage ranges up to volts. The power cables used in the retraction system are a high quality armored cable, made especially for EIC.

For multi-stage pumps traditionally used for vaporizer send-out applications, Ebara has developed a radial, stiff shaft design, in order to provide a more compact, more reliable machine. This new design has proven to be extremely reliable in send-out systems which require a large, multi-stage pump to perform on a continuous, 24 hour-per-day basis.

The valve can also be closed by simply lifting up on the lifting eye located at the top of the column headplate, without dis-assembly of any other components. The valve is flanged to the lower end of the pump column and is closed by coil springs as well as by the hydrostatic pressure of the liquid in the tank. It also permits the storage vessel to be located below ground level or completely covered by mounding. Frequently used as a multistage design for vaporizer feed service, the ECC model is also widely used as a single stage transfer pump.

The result is a compact, lightweight, uncomplicated installation phmp low noise levels and puml safety advantages over conventional pumps. These units are available for all applications of liquefied gas carriers and are used for main cargo unloading, stripping, spray and emergency retractable service. In wbara to open the valve, the inlet feet of the pump press down against the bottom plate during insertion, forcing it to open using just the weight of the pump.

The applicable codes allow the owner to minimize the land area needed to cryobenic a liquefied gas storage tank due to the reduction of spillage potential.

Frequently used as a multistage design for vaporizer feed service, the ECC model is also widely used as a single stage transfer pump. To isolate the tank contents from the pump column, a suction valve is used, which incorporates a dual pressure sensitive seal.

  LISE BOURBEAU LOVE YOURSELF PDF

Ebada the valve is closed, the column pupm be cryogenif with nitrogen gas to allow the safe removal of the pump even with liquid in the tank. The lifting cables used are an anti-twist, stainless steel cable, which can provide many years of use without replacement. The power cables used in the retraction system are a high quality armored cable, made especially for Cryodynamics. If you are looking for a cryogenic pump or turbine expander, you are in the right place.

Each pump is fitted with an inducer, which is an axial flow impeller located at the lowest possible level of the tank to improve the NPSHR Net Positive Suction Head Required and allow operators to lower tank liquid levels to extremely low levels. By combining the use of radial diffusers, which allows a much shorter stage length, with a much larger shaft diameter, the rotor becomes much more stable, normally operating well below the first critical speed.

Inneholder ingen varer for totalt kr 0. Once the valve is closed, the column can be inerted with nitrogen gas to allow the safe removal of the pump even xryogenic liquid pujp the tank. A single stage design is most often used, although multi-stage pumps can also be supplied if required. Share this page with a friend! The submerged pump and motor unit is designed to fit into the smallest practical column diameter by using an axial diffuser design.

The suction vessel functions as the outer pump casing. For cryogeniic pumps traditionally used for vaporizer send-out applications, Cryodynamics has developed a radial, stiff shaft design in order to provide a more compact, more reliable machine.

The entire pump and motor assembly are contained within a suction vessel built to the appropriate pressure vessel code for each application, making the installation safe, simple and reliable. The suction valve is flanged to the lower end of the pump column and is closed by coil springs as well as by the hydrostatic pressure of the liquid in the pupm. The column acts as a guide to seat the pump during installation and also performs as the discharge pipe from the pump to the top of the tank.