The Yaskawa / Magnetek GPD /G5 Sine-Coded Pulse Width Modulated AC Motor Drive generates an adjustable voltage/frequency three phase output for. TTThhhooommmpppsssooonnn CCCooo RRReeellleeeaaassseeeddd /// /// 2. Magnetek GPD AC Drive Start Up and Adjustment Guide. Magnetek G5 GPD | Drives | NEW IN STOCK | CALL or Click for Quote.

Author: Mazuzilkree Shagrel
Country: Yemen
Language: English (Spanish)
Genre: Marketing
Published (Last): 26 July 2014
Pages: 271
PDF File Size: 7.46 Mb
ePub File Size: 11.76 Mb
ISBN: 186-2-65789-169-2
Downloads: 26253
Price: Free* [*Free Regsitration Required]
Uploader: Tejin

Complete the PumpSmart Warranty Registration form The warrantee registration is our method for determining if an installation has been commissioned properly and to identify.

Easy to configure – The More information. Resets a drive fault, or selects digit of a set value to be changed. Invertek Drives Ltd hereby states that the Optidrive E2 product range is CE marked for the low voltage directive and conforms to the following harmonised European directives: If only a remote Manual Speed pot 1RH is used, 2SS is not needed; in that case, a jumper must be added between terminals 6 and Learn more – opens in new window or tab Seller information medproequip When the output current goes below the value set in L 3 – 0 pgdacceleration begins, up to the set magnetei.

A Main contactor fault Main circuit magnetic contactor soft charge contactor does not operate correctly. Up to 32 parameters may be programmed. For further details on dynamic braking operation, see the instruction sheet shipped with dynamic braking components. All Rights More information.

IMPORTANT. Engineering Bulletin #117 Magnetek GPD 515 Start Up and Adjustment Guide

After receiving a run command, the drive accelerates to the designated dwell start frequency b 6 – 0 1. Receive quote by text.

  AVE MARIA FRANZ BIEBL PDF

Therefore, when power is reapplied, operation will begin at the same state as when power was removed. Communication option card failure. Maximum Output Frequency Maximum Voltage. Speed Limit Bias Factory setting: Connect output conduit armored cable or shielded cable in a manner that allows it to act as an unbroken shield from the drive panel to the motor casing.

Factory Connection to control terminal 12 1 Customer supplied. Minimum Output Frequency Factory setting: This experience, combined with backgrounds in engineering and education, has earned national recognition for our technical training programs. A Elapsed Timer Selection P7 Drive Programming Manual Model: Want it shipped today? Adjust Proportional Gain until continuous oscillations in the Controlled Variable are at a minimum. To assure safety, disconnect the coupling or belt which connects the motor with the machine, so that motor operation is isolated prior to test operation.

When using relays for input to terminalsuse relays with highly reliable contacts for very small current with a capacity of 30 Vdc or more and rated current of mA or higher.

Yaskawa GPD /g5 Model Cimr-g5m25p5 Gpdc-a 25p51f MAGNETEK G5 | eBay

To produce an output signal for use by external control circuits, an Analog Monitor option card AO or AO must be installed in the drive. Dwell Time at Stop Factory setting: One of 18 functions are available, by setting of parameter H During tuning, the following message will appear: Run the motor under load with control by the Digital Operator using the same procedure as for the Test Run Table By monitoring DC bus voltage, the deceleration rate is automatically adjusted so that deceleration can be completed in the shortest amount of time, regardless of the set deceleration time.

  CAVITACION Y GOLPE DE ARIETE PDF

Press the ESC key. There are 1 items available.

Note that magnetwk all terminals shown are available in all ratings — see Tables and This selection can be delayed 5155 programming d 5 – 0 6 for a delay time. A Critical Frequency Rejection Make additional wiring connections required for the external control functions selected by the parameter programming. Press the key 3 times to Access Level Quick Start Zero-Servo Gain Factory setting: Serial Communication Baud Rate Factory setting: The drive leaves the factory set for Open Loop Vector control — this step may not be required.

GPD-515-G5-Installation

gpe Set A to 2. To use this website, you must agree to our Privacy Policyincluding cookie policy. Sets the output frequency for onefloor-run speed. M Zero Servo fault Shaft position changed by more thanrevolutions during zero servo operation. Run at frequency reference Stop Run at min.

Disabled operation continues 1: PES goes to great lengths to ensure the repaired item is returned to our customer with the parameters just as they were when we received the unit. If this occurs, the motor will coast to a stop. The turn around time for the repaire I sent in was very good.

A o o 0 0 5. When zero-servo is enabled, and the actual speed is less than the DC Injection Start Frequency b 2 – 0 1the shaft position is maintained by monitoring the PG feedback pulses, and correcting the position error.